Immunofluorescence Assay to Evaluate Effect of Target Proteins on Neurite Outgrowth

Published: April 30, 2023

Abstract

Source: Chan, W., W., R. et al. An Enhanced Green Fluorescence Protein-based Assay for Studying Neurite Outgrowth in Primary Neurons. J. Vis. Exp. (2019).

In this video, we demonstrate an EGFP-based immunofluorescence assay to identify the efficacy of target proteins on the neurite outgrowth of primary cortical neurons. The primary neurons are transfected with a fluorescent protein, EGFP, and a target protein, and then an immunoassay is performed to investigate the effect of the target protein on neurite outgrowth.

Introduction

1. Preparation of Coverslips

  1. Place a sterile 18 mm circular coverslip into each well of a 12-well tissue culture plate.
  2. Coat the coverslip with 5 µg/mL poly-D-lysine solution in a humidified 37 °C incubator for at least 1 hr.
  3. Aspirate the poly-D-lysine solution from the tissue culture plate and rinse the coated coverslips once with sterile water.

2. Cell Transfection and Fixation

NOTE: All procedures in step 2 are performed inside a Class II Biosafety cabinet.

  1. Transfect 0.5 µg of EGFP construct (pEGFP-C1) to primary cortical neurons together either with or without 0.5 µg of POI by using 1 µL of transfection reagent (e.g., Lipofectamine 2000). Use the manufacturer's instructions.
    NOTE: Mammalian expression constructs were prepared by using an endotoxin-free plasmid preparation kit. Treatment with chemicals/molecules (in this manuscript cytochalasin D (Cyto D) and nerve growth factor (NGF) were used) can be done at 6 hr after transfection.
  2. Aspirate the culture medium 24 h post-transfection and wash the transfected cells once with 37 °C PBS (10 mM sodium phosphates, 2.68 mM potassium chloride, 140 mM sodium chloride).
  3. Fix the cells with 4% paraformaldehyde in PBS for 10 min in the dark at room temperature.
  4. Wash the fixed cells three times with PBS.
  5. Add a minimal amount of fluorescence mounting medium on a microscope glass slide. Carefully transfer the coverslip from the 12-well plate onto the mounting medium with the sample facing the glass slide.
    NOTE: Seal the edge of the coverslip with nail polish if an aqueous mounting medium is used.

3. Measurement of Neurite Outgrowth

  1. Use a 40x objective for capturing images using an epi-fluorescent microscope.
  2. Capture images from at least 40 intact neurons with EGFP signal per transfection.
  3. Open the captured image in ImageJ software with the NeuronJ plugin to measure the length of the longest neurite, from the cell body to the tip of the growth cone, of each imaged neuron.
  4. Analyze the data obtained with the software to determine the effect of the targeted proteins in neurite outgrowth.

Disclosures

The authors have nothing to disclose.

Materials

18 mm Circle Cover Slips Thermo Scientific CB00180RA Sterilize before use
Cytochalasin D Invitrogen PHZ1063 Dissolved in DMSO
EndoFree Plasmid Maxi Kit QIAGEN 12362
Fluorescence Mounting Medium Dako S302380
Lipofectamine 2000 Transfection Reagent Invitrogen 11668019
Paraformaldehyde Sigma-Aldrich P6148
pEGFP-C1 Clontech #6084-1
pCI FE65 Please see references 8 and 15
PBS Tablets Gibco 18912014
Penicillin-Streptomycin Gibco 15140122
Poly-D-lysine hydrobromide Sigma-Aldrich P7280
Spatula Sigma-Aldrich S4147
Trypsin-EDTA (0.05%), phenol red Gibco 25300062

Tags

Play Video

Cite This Article
Immunofluorescence Assay to Evaluate Effect of Target Proteins on Neurite Outgrowth. J. Vis. Exp. (Pending Publication), e21331, doi: (2023).

View Video