We designed a procedure in which a formaldehyde-fixed human cadaver is used to assist neurosurgeons in training for the implantation of microelectrode arrays into the neocortex of the human brain.
This protocol describes a procedure to assist surgeons in training for the implantation of microelectrode arrays into the neocortex of the human brain. Recent technological progress has enabled the fabrication of microelectrode arrays that allow recording the activity of multiple individual neurons in the neocortex of the human brain. These arrays have the potential to bring unique insight onto the neuronal correlates of cerebral function in health and disease. Furthermore, the identification and decoding of volitional neuronal activity opens the possibility to establish brain-computer interfaces, and thus might help restore lost neurological functions. The implantation of neocortical microelectrode arrays is an invasive procedure requiring a supra-centimetric craniotomy and the exposure of the cortical surface; thus, the procedure must be performed by an adequately trained neurosurgeon. In order to provide an opportunity for surgical training, we designed a procedure based on a human cadaver model. The use of a formaldehyde-fixed human cadaver bypasses the practical, ethical and financial difficulties of surgical practice on animals (especially non-human primates) while preserving the macroscopic structure of the head, skull, meninges and cerebral surface and allowing realistic, operating room-like positioning and instrumentation. Furthermore, the use of a human cadaver is closer to clinical daily practice than any non-human model. The major drawbacks of the cadaveric simulation are the absence of cerebral pulsation and of blood and cerebrospinal fluid circulation. We suggest that a formaldehyde-fixed human cadaver model is an adequate, practical and cost-effective approach to ensure proper surgical training before implanting microelectrode arrays in the living human neocortex.
Recent years have seen the development of technological solutions to the challenge of recording the activity of multiple individual neurons in the living brain1,2,3. Silicon-based microelectrode arrays perform similarly to conventional wire microelectrodes in terms of signal properties, and they can record from dozens to hundreds of neurons in a small patch of cerebral tissue4,5,6,7. Microelectrode arrays have allowed scientists to establish the correspondence between neural activity in the primary motor cortex of monkeys and arm movements8, which in turn has provided a boost to the development of brain-computer interfaces (BCIs)9.
Microelectrode arrays have been used in humans in two situations: as chronic implants to control BCIs and as semi-chronic implants to study the activity of individual neurons in patients suffering from epilepsy. Chronic implants, targeting the functional representation of the hand in primary motor cortex, have allowed patients suffering from tetraplegia to control the motion of a robotic arm or of computer cursors10,11,12,13. Semi-chronic implants, inserted together with subdural electrocorticography (ECOG) electrodes in patients with drug-resistant epilepsy who are candidates for epilepsy surgery14, allow single-unit recordings before, during and after seizures, and have begun to shed light on the activity of single neurons during and in between epileptic seizures15,16,17,18,19. Microelectrode arrays have the potential to significantly improve our understanding of how the brain functions by establishing a link between the activity of neurons, on the one hand, and the perceptions, movements and thoughts of human beings, both in health and in disease, on the other20,21.
Silicon-based microelectrode arrays are now available commercially and their use in humans has been approved by regulatory authorities in the USA in the semi-chronic epilepsy indication. However, these devices are invasive and must be inserted into the brain. The negative consequences of improper insertion technique, beyond the failure of the device to record neuronal activity, include cerebral hemorrhage and infection, with the potential for long-lasting or permanent neurological dysfunction. Although the complication rate of microelectrode array implantation is currently unknown, the rate of potentially serious complications during the implantation of intracranial electroencephalography (EEG) macroelectrodes is 1-5%22,23. Therefore, the proper implantation of microelectrode arrays requires both extensive neurosurgical skills and procedure-specific training.
The approaches available for surgeons to hone their skills with microelectrode arrays in a safe environment include non-human mammals and human cadavers. The ideal training model would faithfully reproduce the size and thickness of the human skull; the toughness and vascular ramification of the dura; the gyrification pattern, consistency and pulsation of the human brain; the presence of circulating blood and cerebrospinal fluid; and the overall positioning of the subject in an operating room (OR)-like environment. Thus, animal models need to be of a sufficient size to provide a meaningful experience to the surgeons. Large non-human primates come closest, but their use for surgical training is unsustainable both from an ethical perspective and because they are expensive. Rodents do not enter consideration because of their small size; using even cats or rabbits implies diverging significantly from an OR-like environment.
Human cadavers represent an attractive alternative. Their advantages include the life-like size and shape of the head and brain and the possibility of setting up surgical training in an OR-like environment. The most obvious departures from a realistic situation are the absence of cerebral pulsations and bleeding and the modifications in the aspect and consistence of body tissues that are specific to the technique employed for cadaver preservation24. Fresh-frozen cadavers preserve the consistency and flexibility of many organs and tissues to some extent, but they have several drawbacks: they start degrading as soon as thawing begins, so that the brain becomes too degraded for the insertion of a microelectrode array to be performed realistically, and they are a relatively rare and expensive resource. Formaldehyde-fixed cadavers, on the other hand, are more affordable and available and much more durable, at the expense of hardened tissue consistency.
Here, we establish a procedure using a formaldehyde-fixed human cadaver model to provide neurosurgical training for the implantation of a neocortical microelectrode array. Our approach allows realistic, OR-like positioning and instrumentation; performing craniotomy and durotomy and exposing the neocortical surface; attaching the electrode pedestal to the skull bone neighboring the craniotomy; and inserting the microelectrode array into the neocortex with a pneumatic impactor25. Critically, it enables surgeons to practice the precise alignment of the microelectrode array (which is connected to the electrode pedestal by a bundle of individually insulated gold wires) parallel to the neocortical surface26. Our protocol faithfully replicates the indication of microelectrode array implantation together with ECOG implantation in patients who are candidates for epilepsy surgery. The particulars of the implantation surgery are influenced significantly by the exact type of microelectrode array; here, we describe the procedure for an array that recently received regulatory approval for use in humans in the USA. The so-called Utah array comprises a 4×4 mm, 100 microelectrode grid; a transcutaneous pedestal that is attached to the external table of the skull; and a wire bundle connecting the two.
The human cadaver used in this work was provided under the framework of body donations for medical education. Informed consent for body donation was obtained in writing during the lifetime of the donor. In accordance with the federal and cantonal laws, no review by an ethics committee was necessary.
Note: This protocol assumes that the persons performing the practice surgery are neurosurgeons with training and expertise in standard neurosurgical procedures, including patient positioning and head fixation, craniotomy and durotomy, and suturing. In addition to the tools and equipment specific to the microelectrode array, standard neurosurgical tools and equipment are used.
1. Selection of the cadaver and setup of the operating room
2. Exposure of the neocortical surface
3. Fixation of the electrode pedestal
4. Positioning and insertion of the microelectrode array
5. Positioning of the subdural ECOG grid
Note: This step is optional.
6. Repositioning and closure of the dura mater, bone flap, and skin flap
Our protocol uses a formaldehyde-fixated human cadaver model to allow surgeons to practice the surgical procedure of implanting a microelectrode array into the cerebral neocortex in a realistic, OR-like environment. The option of performing post-mortem neuroimaging, such as head CT, will confirm the absence of any significant intracranial lesion (Figure 1A) and can help with the selection of the implantation site. Working with an entire specimen and setting up for surgery on an operating table increases the realism of the training procedure (Figure 1B-1C). Although formaldehyde fixation somewhat alters the color, texture and stiffness of the body tissues, each step of the surgical procedure to expose the neocortical surface (skin incision, craniotomy and durotomy) can be performed easily according to standard neurosurgical practice (Figure 1D and Figure 2A-2C).
The steps of the surgical procedure that are specific to the microelectrode array proceed very similarly to the in vivo situation. The first step consists of screwing the electrode pedestal to the skull bone near the craniotomy ( Figure 2D-2E). Bringing the microelectrode array into alignment with the neocortical surface is one of the most delicate steps of the procedure (Figure 3A)26. The positioning and operation of the pneumatic impactor are also performed in realistic fashion (Figure 3B). Our training protocol provides ample opportunity for surgeons to experiment with these crucial steps. One departure from lifelike realism is the absence of cerebral pulsation in a cadaver model (the slight upwards and downwards movements of the exposed neocortical surface caused by heartbeats and breathing). Nevertheless, the end result of the training protocol (Figure 3C-3E) closely reproduces the real-life situation26.
If performed by two surgeons, the average operative time for microelectrode array implantation is under 30 minutes, as also reported by others26.
Figure 1. Setting up the operating room-like environment. (A) Head CT scan can confirm the absence of any significant intracranial lesion. (B) Position the head in the skull clamp. (C) Drape the head. The specimen's nose is to the right of the picture, the occiput to the left. (D) Incise and recline scalp and temporalis muscle. Please click here to view a larger version of this figure.
Figure 2. Exposing the neocortical surface and attaching the electrode pedestal. (A) Perform a large square craniotomy. (B) Perform durotomy. (C) Reflect the dura mater and expose the neocortical surface. (D) Screw the electrode pedestal to the skull bone near the edge of the craniotomy (inset: close-up on the fixation of the pedestal with bone screws). (E) Hold the fragile microelectrode array with tweezers to avoid damage from unwanted contact. Please click here to view a larger version of this figure.
Figure 3. Positioning and inserting the microelectrode array. (A) Bend the wire bundle in order to bring the microelectrode array into alignment with the cortical surface (inset: close-up on the alignment of the microelectrode array and cortex). (B) Bring the pneumatic impactor into alignment with the back of the microelectrode array (inset: close-up on the alignment of the impactor and microelectrode array). (C) Overview of the microelectrode array, wire bundle and electrode pedestal. (D) Position ECOG grid over the cortical surface. (E) Close skin around the neck of the electrode pedestal. Please click here to view a larger version of this figure.
The formaldehyde-fixed human cadaver model and the surgical protocol described here replicate the surgical procedure of implanting microelectrode arrays into the human cerebral neocortex. Each step of the procedure, including the positioning of the microelectrode array and its insertion with the pneumatic inserter, proceed in almost the same fashion as in a real-life patient, with the exception that cerebral pulsation and circulation are absent. The critical steps in the protocol are the alignment of the microelectrode array with the neocortical surface and its impaction into the cortex using the pneumatic inserter. Care must be taken to approximate the array as parallel to the cortical surface as possible. In the case that the array does not lie flush with the neocortical surface after the first tap of the pneumatic inserter, one additional tap can be delivered. Throughout the procedure, the microelectrode array should be protected from mechanical damage. In the case of implantation in a human patient in clinical conditions, if there is any visible damage to the microelectrodes, bundle or connector, the array should be discarded and another one used.
The Utah array is currently the only neocortical microelectrode array that has received regulatory approval for use in humans. However, other types of microelectrodes have been developed in animals and may be used in humans within specific research projects28. Each approach carries its own advantages and drawbacks, mostly related to the design of the electrodes. For instance, the ballistic insertion technique of the Utah array, which was developed out of necessity25, requires that the array be precisely aligned with the cortical surface; this requirement does not necessarily apply to other microelectrodes, which can be pushed gently into the gray matter. Some electrodes allow access to the activity of all cortical layers29, whereas the Utah array samples from neurons at a single, predetermined depth. One of the major advantages of the Utah array is the large number of neurons that can be recorded simultaneously, making it particularly appropriate for motor BCIs11.
For neurosurgical laboratory training courses, cadaveric specimens are considered as models of high value, allowing haptic feedback in an environment presenting specifically human anatomy30,31. There is no universal cadaver model, however, and the embalming technique must be adapted to each procedure's objectives: are soft tissues (such as the scalp) of importance, or rather the bones, dura mater, cortex, ventricles, or blood vessels32,33,34,35,36? Fresh or fresh-frozen (cryopreserved) specimens, while frequently considered as the best model for a variety of surgical procedures, carry the risk of transmitting infectious diseases. Furthermore, they have a very limited working time because of fast decay31,37,38,39, followed by decreased tissue compliance, ventricular collapse and pneumocephalus35. In the case of our protocol, maintaining a somewhat firm cortical surface was a requirement to enable the insertion of the microelectrode array, thus precluding the use of a fresh-frozen specimen. Embalming solutions providing long-term fixative and germicidal properties are also widely accepted30,33,35,40. Cadavers embalmed according to the Thiel fixation are highly regarded in terms of soft tissue consistency and for developing fascial or internervous planes36, but the preservation of the brain is thought to lack realism41. Formaldehyde-based fixation causes tissue stiffening and retraction as well as discoloration35,36,37. However, formaldehyde fixation is widely available and affordable, and formaldehyde-fixed cadavers are very durable. In the context presented in this paper, the hardening of soft tissues caused by formaldehyde fixation, while being a disadvantage for many surgical training courses (in particular for orthopedic approaches), turned out to be an adequate model, presenting a stable, but not too rigid surface of the brain, thus allowing for a realistic application of the cortical microelectrode array on the post mortem brain. Techniques have been developed to simulate the circulation of blood and cerebrospinal fluid in formaldehyde-fixed cadavers30,31,39 and could complement the present protocol in order to further increase the realism of the OR-like environment.
Three-dimensional (3D) printing has recently become an accessible and affordable means of replicating body parts for medical and surgical education. Novel 3D printing and molding using synthetic gelatinous casts provides a realistic brain model with tactile feedback. This approach has the advantage of providing a deformable structure that can be printed to reproduce a particular individual's cerebral anatomy and is thus more anatomically accurate than more generic models42. On the other hand, there are still reservations concerning the stiffness and the tissue cutting properties of the synthetic material43. In this sense, the cadaveric model gives a broader anatomical framework, including the complete stratigraphy, not only the brain surface itself.
An alternative to surgical training on human cadavers is practicing on live animals. Implanting a microelectrode array on a primate model, for instance a macaque monkey, would reproduce most of the features of the actual procedure in a human patient, including surgical positioning and instrumentation similar to those used in humans, a gyrencephalic brain of a size not very far from that of a human's, and the presence of cerebral pulsation as well as blood and cerebrospinal fluid circulation. However, while it is acceptable to implant microelectrode arrays in monkeys for the purpose of neuroscience research, using monkeys solely for surgical training is widely discouraged, for ethical reasons as well as because of their very high cost. Because few neuroscience centers implant microelectrode arrays in monkeys for research purposes, and because these centers use few animals at a time (due to the cost of the monkeys themselves and the long and labor-intensive training that neuroscience research with monkeys generally entails), training for microelectrode array implantation in monkeys is not an option for most surgeons. Using smaller animals, such as rodents and even cats or rabbits, would depart too much from OR-like realism. One potential advantage of animal models is that tissue healing allows repeating the entire procedure more than once over the lifetime of the animal. In a human cadaver model, the entire procedure can be repeated once per hemisphere. That being said, craniotomy does not present any particular difficulty to a trained neurosurgeon. Provided that the craniotomy is large enough, the specific steps of pedestal fixation and microelectrode positioning and insertion can be repeated as often as desired during a given session, providing an adequate training opportunity for more than one surgeon. Thus, we think that embalmed human cadavers are the most appropriate model to train surgeons to implant microelectrode arrays.
Recent breakthroughs in BCI development suggest that microelectrode arrays could represent a clinically significant addition to the therapeutic and restorative solutions that are available today for patients with severe motor or communicative disabilities11,13,44. In the near future, the implantation of microelectrode arrays might thus become a required part of the training of neurosurgeons. Refinements in the design of the microelectrodes themselves, together with improvements in connecting the electrodes to the computer processing neuronal signals (likely through wireless connections), will reduce the invasiveness of microelectrode arrays and further enhance their usability for both the physicians and the patients and their caregivers.
The authors have nothing to disclose.
The authors are grateful to Dr. Rob Franklin (Blackrock Microsystems), Prof. Margitta Seeck (Division of Neurology, Geneva University Hospitals, Geneva, Switzerland), Dr. Andrea Bartoli and Prof. Karl Schaller (Division of Neurosurgery, Geneva University Hospitals, Geneva, Switzerland), and Mr. Florent Burdin and Prof. John P. Donoghue (Wyss Center for Bio and Neuroengineering, Geneva, Switzerland) for their support in preparing the present work.
Mayfield skull clamp | Integra LifeSciences, Cincinnati, OH | A1059 | |
Midas Rex MR7 system for craniotomy | Medtronic, Minneapolis, MN | EC300 | |
Dura scissors | Sklar Surgical Instruments, West Chester, PA | 22-2742 | |
Self-tapping bone screws | OrthoMed Inc., Tigard, OR | OM SYN211806 | |
Microelectrode array and pedestal | Blackrock Microsystems, Salt Lake City, UT | LB-0612 | Mock-up arrays are available from the manufacturer upon request |
Pneumatic impacter | Blackrock Microsystems, Salt Lake City, UT | LB-0088 | |
64-channel electrocorticography grid | Ad-Tech Medical Instrument Corporation, Racine, WI | FG64C-SP10X-0C6 | Optional |