We demonstrate the use of patterned aerosol adhesives to construct 3D paper microfluidic devices. This method of adhesive application forms semi-permanent bonds between layers, enabling single-use devices to be non-destructively disassembled after use and to ease folding complex nonplanar structures.
We demonstrate the use of patterned aerosol adhesives to construct both planar and nonplanar 3D paper microfluidic devices. By spraying an aerosol adhesive through a metal stencil, the overall amount of adhesive used in assembling paper microfluidic devices can be significantly reduced. We show on a simple 4-layer planar paper microfluidic device that the optimal adhesive application technique and device construction style depends heavily on desired performance characteristics. By moderately increasing the overall area of a device, it is possible to dramatically decrease the wicking time and increase device success rates while also reducing the amount of adhesive required to keep the device together. Such adhesive application also causes the adhesive to form semi-permanent bonds instead of permanent bonds between paper layers, enabling single-use devices to be non-destructively disassembled after use. Nonplanar 3D origami devices also benefit from the semi-permanent bonds during folding, as it reduces the likelihood that unrelated faces may accidently stick together. Like planar devices, nonplanar structures see reduced wicking times with patterned adhesive application vs uniformly applied adhesive.
In recent years, paper microfluidics has garnered considerable popularity for its potential to provide low-cost point of care (POC) diagnostic devices.1-3 POC devices offer functionality similar to those of lab-based tests in a format that allows results to be obtained relatively quickly. POC devices made from paper are low-cost, lightweight, and easy-to-use alternatives to expensive microfluidic chips and miniaturized laboratories, making them ideal for use in resource-limited settings. The most common paper microfluidic devices are one-dimensional lateral flow devices, but planar three-dimensional (3D) paper microfluidic devices hold promise to provide multiplexed diagnostic devices4 that take up a much smaller footprint than would be required by a 2D device5 and correspondingly use a smaller sample volume.
Initially, planar 3D paper microfluidic devices were assembled individually, layer-by-layer with patterned paper layers alternating with laser-cut double-sided tape. Carefully aligned holes cut in the tape layer were filled with cellulose powder to ensure inter-layer fluid transport.4 A number of alternate methods were subsequently developed,6-9 each improving different aspects of the devices. In particular, by eschewing adhesives, devices could be folded via origami techniques with layers held together by an external clamp.8 This eliminates any potential adhesive interference in a diagnostic test and allows the device to be unfolded post-use, potentially allowing even smaller sample volumes by displaying results internally. Alternatively, by using an aerosol adhesive applied between each paper layer, sheets of devices could be assembled simultaneously, without time-consuming patterning and alignment of tape.9
However, by applying an aerosol adhesive through a stencil, it is possible to gain the benefit of both of these techniques. By spraying the adhesive through a stencil, only a fraction of the adhesive is applied to the device, minimizing any potential interference with interlayer fluid transfer. Additionally, with careful stencil selection, a pattern of adhesive can be applied that results in semi-permanent adhesive bonding, allowing devices to be unfolded after use, while still providing sufficient interlayer contact to allow fluid to wick between layers.
Finally, applying aerosol adhesives through a stencil eases the construction of nonplanar 3D paper microfluidic devices, by minimizing the amount of adhesive applied to adjacent faces that may require frequent folding and unfolding during construction.10 Additionally, the use of patterned adhesive enables device to be unfolded after use for more convenient storage. Nonplanar 3D paper microfluidic devices are expected to be used for tasks that would otherwise be impossible in a planar 3D device. Figure 1 depicts the general process flow used to construct both planar and nonplanar 3D devices.
The above protocols use perforated metal sheets as stencils for applying aerosol adhesives to construct planar and nonplanar 3D paper microfluidic devices. In planar devices, this has the advantage of allowing devices to be completely unfolded after the adhesive has dried without destroying the device. In other adhesive based construction techniques, this is almost impossible, although, some designs allow for partial destructive disassembly by unpeeling two halves held together with a removable adhesive.14 Adh…
The authors have nothing to disclose.
This work is supported by a fund from Bourns College of Engineering of University of California, Riverside. BK received a scholarship from the Lung-Wen Tsai Memorial Award in Mechanical Design.
Camera | Nikon | D5100 | |
Solid-ink printer | Xerox | ColorQube 8880 | |
Hotplate | Torrey Pines | HS60 | |
Humidity chamber | Electro-Tech Systems | 5503-E | |
Spray adhesive | 3M | 62497749309 | Super 77 (16.75 oz can) |
Filter paper | Whatman | Grade 4 | |
Perforated steel sheet | MetalsDepot | PS16116 | |
Tartrazine | Sigma-Aldritch | T0388 | |
Allura Red | Sigma-Aldritch | 458848 | |
Erioglaucine disodium salt | Sigma-Aldritch | 861146 |