This video protocol demonstrates a method for generating transgenic Xenopus laevis by introduction of transgenes into sperm nuclei followed by nuclear transplantation into unfertilized eggs.
Stable integration of cloned gene products into the Xenopus genome is necessary to control the time and place of expression, to express genes at later stages of embryonic development, and to define how enhancers and promoters regulate gene expression within the embryo. The protocol demonstrated here can be used to efficiently produce transgenic Xenopus laevis embryos. This transgenesis approach involves three parts: 1. Sperm nuclei are isolated from adult X. laevis testis by treatment with lysolecithin, which permeabilizes the sperm plasma membrane. 2. Egg extract is prepared by low speed centrifugation, addition of calcium to cause the extract to progress to interphase of the cell cycle, and a high-speed centrifugation to isolate interphase cytosol. 3. Nuclear transplantation: the nuclei and extract are combined with the linearized plasmid DNA to be introduced as the transgene and a small amount of restriction enzyme. During a short reaction, egg extract partially decondenses the sperm chromatin and the restriction enzyme generates chromosomal breaks that promote recombination of the transgene into the genome. The treated sperm nuclei are then transplanted into unfertilized eggs. Integration of the transgene usually occurs prior to the first embryonic cleavage such that the resulting embryos are not chimeric. These embryos can be analyzed without any need to breed to the next generation, allowing for efficient and rapid generation of transgenic embryos for analyses of promoter and gene function. Adult X. laevis resulting from this procedure also propagate the transgene through the germline and can be used to generate lines of transgenic animals for multiple purposes.
For each transgenic construct to be tested, we generally transplant nuclei into 500-1000 eggs; at this scale, we can generate transgenic embryos expressing up to 10 different constructs per day, depending on how many females are induced to lay eggs. Of these transplantations, about one third of the eggs cleave and 60-80% of these cleaving embryos proceed through gastrulation normally. Depending on the reaction conditions used, between 10-50% of these embryos express the transgene of interest. Therefore, once this procedu…
The authors have nothing to disclose.
Funding for our work is provided by the NIH, the March of Dimes, and the American Cancer Society.
A.Sperm nuclei preparation
Reagents:
Equipment:
B. Preparation of High Speed Extract
Reagents:
Equipment:
C. Nuclear transplantation.
Reagents:
Equipment:
Agarose dishes for injection: In a 60 mm plastic petri dish, lay a small 35mmX35mm weigh boat on molten 2.5% agarose in water 0.1XMMR to create a depression with an agarose-coated bottom for filling with eggs. Once agarose has hardened, wrap in parafilm and store at 4°C until use. Make 2-3 dishes in advance for each transgenic reaction you plan to do.
Infusion pump: We use a single syringe infusion pump from Harvard Apparatus, equipped with a 3 cc syringe/needle filled with mineral oil (Sigma M-8410). Blunt the syringe needle tip (to keep it from perforating the tubing) and attach the fine tygon tubing. Run the pump at ~10nl/sec; this assumes that the time the needle is in each egg will be no greater than 1 sec. Pump should be pre-run for several minutes prior to starting transgenesis for the day to assure that the plunger for the syringe is flush with the piston and that steady positive flow of oil out of the tubing is occurring.
Needles for nuclear transfers. Using a micropipette puller, generate needles with long, sloping tips. Clip these with a forcep under a dissecting microscope equipped with an ocular micrometer to obtain an ~80 micron opening with a beveled shape.
Other equipment: Xenopus laevis females, stereomicroscope, incubator, micromanipulator, microinjection needle puller (e.g. Model P-87, Sutter), syringe needles (26 gauge), glass microinjection needles, ocular micrometer for calibrated clipping of microinjection needle tips to 80μm diameter, petri dishes, weigh boats 35mm, Tygon tubing (ID=1/32 in., OD=3/32 in.)